Eberline

Now a subsidiary of Thermo Scientific

Info on getting my alpha probes working

Recent thread on reading iButton: [1]

Thermo Electron Smart connector

XLR7 mini?
- No its 7 male pins + 1 HV pin
Manual refers to it as "YP11579050 smart probe harness"
Disassembled more: VIKING … 12

SHP380AB

Connector: calling the connector with 7 male pins and 1 female pins "male" since its predominately male. This is the connector used on sensors (and meter too probably). Female HV pin is pin 1. Looking into the male connector with the female HV socket at the bottom, pin 2 clockwise from it and continues. The center pin is pin 8.

My pin	Sch pin	Sch label	What	Color
1	1	HV COAX	HV+	Coax-center	+800 V nomal 1300 V max
2	2	BRAID	HV common Chassis	Coax-shield
3	3	SIGNAL GROUND	1Wire-GND	White-Black
4	6	TOUCH MEMORY	1Wire-D	White-Red
5	7	+5V	N/C flying	White-Orange
6	8	NON-MEMORY PROBE	N/C flying	White-Yellow
7	4	BRAID	HV common Chassis	Coax-shield
8	5	MEMORY PROBE	1Wire-GND	White-Green

Straight: anode? Higher voltage

Other, usually curved, must be cathode then

Picture showing reading iButton out: [2]

Power

70M dynode string draws nominal 11.4 uA @ 800V
1300V max

Manuals/Eberline/HP-380 and SHP-380/HP-380AB SHP-380AB HP-380A SHP-380A Technical Manual1.pdf Manual link

Manual

Typical units
- Eberline E-600
- Eberline RM-24
HP: MHV connector, no memory
Different phosphor plates
- HP/SHP-380A: single for alpha
- HP/SHP-380AB: dual for alpha + beta
Active area: 2.72" x 5.7" => 100 cm**2
Window thickness
- HP/SHP-380AB: 0.87 mg/cm2 aluminum plastic film
- HP/SHP-380A: 0.58 mg/cm2 aluminum plastic film
- Mylar
Alpha efficiency
- Source: 1/32" plated Pu-239
- HP/SHP-380AB: 18% typical, 4pi
- HP/SHP-380A: 21% typical, 4pi
SHP connector
- Eberline smart probe
- Cable: CA-100-xx
  - xx = length in inches
  - 36, 60 standard
- Simple HV cable adapter
  - CA-99-xx

** Marketed "MHV to Eberline smart probe" but works for smart probe to MHV as well

- - CA-102-xx: BNC to eberline smart probe
  - CA-103-xx: CP-1 connector
Recommend no more than 0.25" from aplha source
WinE600 computer program used to calibrate?
- Sounds like it has automated checkout
Recommends using lacquer to repair punctured window
Strongly warns against using solvents on scintilator
No evidence scintilator is super sensitive to moisure
Has rough schematic w/ pinout

Pin	Label
1	HV COAX
2	BRAID
3	SIGNAL GROUND
4	BRAID
5	MEMORY PROBE
6	TOUCH MEMORY
7	+5V	N/C If N/C, how is the memory powered? Unclear above signals
8	NON-MEMORY PROBE	N/C

Probe comes apart very easily by unscrewing either side of the PMT assembly. PMT markings

TUBE TYPE: PB29B02H-1

PCB is very simple…basically the resistor chain in the schematic plus two capacitors. Mixed 0603 resistors + through hole capacitors

Electrical tape blob…memory? Not terrible, but could be more elegant. Round…Dallas iButton? ⇒ 1wire if so

An iButton!

DS1993L-F5
IBUTTON MEMORY 4KBit F5
[3]
BusPirate? [4]

Wire colors

Black: ground
Red: ibutton-. Tied to red
Yellow: N/C
Green: ibutton-. Tied to red
Orange

eBay 1

Source

Seller has 7 of them. Wants 300 each

eBay 2

Seller had two of them. Wanted 140 each. After a bit of back and forth, this is what I purchased 2 @ 120 each. They might have more…have sold 3 so far, listing 2 at a time

One has NAVSEADET sticker. "NAVSEADET stands for Naval Sea Systems Command Detachment". Mine didn't have it when it arrived, so must have been stock photo from earlier auction