Difference between revisions of "Hamamatsu source"
| Line 5: | Line 5: | ||
HAMAMATSU PHOTONICS L7902 (head) & C8033-01 (controller) | HAMAMATSU PHOTONICS L7902 (head) & C8033-01 (controller) | ||
| − | + | = Pony controller = | |
"Pony Hamamatsu DR2 X-ray System X-RAYCONTROL Unit for PXG-090W & Cables" | "Pony Hamamatsu DR2 X-ray System X-RAYCONTROL Unit for PXG-090W & Cables" | ||
| Line 12: | Line 12: | ||
| − | + | == serial == | |
25 pin serial. Used a DB25 to DB9 adapter and was able to get the message "ERROR" when I pressed enter | 25 pin serial. Used a DB25 to DB9 adapter and was able to get the message "ERROR" when I pressed enter | ||
| − | + | == interlock1 == | |
2 wires. Came with shorting plug | 2 wires. Came with shorting plug | ||
| Line 25: | Line 25: | ||
Why isn't interlock1 and interlock2 in series? Do they serve different purposes? | Why isn't interlock1 and interlock2 in series? Do they serve different purposes? | ||
| − | + | == interlock2 == | |
4 wires used in case | 4 wires used in case | ||
| Line 38: | Line 38: | ||
| − | + | == Internals == | |
SW1: all LEDs on front light when pressed. No serial output | SW1: all LEDs on front light when pressed. No serial output | ||
| − | |||
| − | |||
MCU: TMP96C141BF | MCU: TMP96C141BF | ||
Revision as of 21:56, 1 June 2022
Head controllers are yellow
Hamamatsu Photonics Softex L7452 X-Ray Tube Unit L7452
HAMAMATSU PHOTONICS L7902 (head) & C8033-01 (controller)
Pony controller
"Pony Hamamatsu DR2 X-ray System X-RAYCONTROL Unit for PXG-090W & Cables"
Couldn't get x-ray on. While interlock1 came shorted, interlock2 is not. Suspect that is the issue and a yellow light will come on
serial
25 pin serial. Used a DB25 to DB9 adapter and was able to get the message "ERROR" when I pressed enter
interlock1
2 wires. Came with shorting plug
Internally appear to go to J1
Why isn't interlock1 and interlock2 in series? Do they serve different purposes?
interlock2
4 wires used in case
- 1: red
- 2: orange
- 3: white
- 4: gray
Red and orange go to J11 near large MATSUSHITA relay
Think white and gray go to J9 along with a few other wires
Internals
SW1: all LEDs on front light when pressed. No serial output
MCU: TMP96C141BF
$ strings c8033-11_v1.0.5.p9_2012-01-06.bin
FOXf
??n1
Micro Foucus X-Ray 130kV Controller
Version 1.03p 00/03/25 sat.
KOU PLANNING CO.LTD.
@h1!
?9sp
?6w^
?9cI
?9c8
?9c'
HIV CUR PHV PCU AGN RST
ERR
ERROR
X-RAY ON
X-RAY OFF
HIV
CUR
PHV
PCU
OVER
NORMAL
INTER LOCK
AGING
AGING
READY
NOT READY
BUSY
REMOTE
LOCAL
RESPONSE
STANDBY
CAMERA POWER
SMALL
LARGE
Micro Foucus X-Ray Controller
Version 1.03p 00/03/25 sat.
KOU PLANNING CO.LTD.
Control commands
HIV_0-1300 CUR_0-300
PHV_0-1300 PCU_0-300
AGN_N_N XON XOF
CXT RST CFL CFS
Status commands
STX SHV SCU SPV
SPC SOV SIN SAG
STS SRB SRL DAG
9;1d
DRSLVMFHGN!BTO$x
x= x
gH[;(
?.fE
<8Db
@0000
address : +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F 0123456789ABCDEF
---------------------------------------------------------- ----------------
PCR XWA XBC XDE XHL XIX XIY XIZ XSP
Version 0.04a 94/06/02 thu.
ERROR
xwa:
xbc:
xde:
xhl:
xix:
xiy:
xiz:
xsp:
pcr:
sr:
spend:
usec
TLCS-900 Remote Debugger Version 0.04a
KOU PLANNING CO. LTD. 94/06/02 thu.
D[(start),(end)] : memory dump
R : register display
S[add] : set memory
G[(add),(break)] : jump to add.
N[(add),(break)] : jump to add.
L[offset add] : load file
M(source),(end),(dist) : move memory
F(start),(end),(data) : fill memory
H : help massage
V : version
?.fE
